Question 1

300-615-page127-image10

Refer to the exhibit. An engineer deploys a SAN environment with two interconnected Cisco MDS 9000 Series

Switches. When the engineer attempts a zone merge, it fails with the error that is presented in the exhibit.

Which action resolves the issue?

Options :

A : Import or export a zone set between the switches to synchronize the switches.

B :

Change the name of one of the zones to match the other zone set.

C :

Ensure that the zone members have different names.

D : Set the distribute policy of the zone to full.

Answer: C

Question 2

'A network engineer troubleshoots an issue at a Cisco data center environment with these conditions:

* The data center has Cisco Nexus 9000 Series Switches running the vPC setup.

* The gateway of the servers is an HSRP IP address between the VLAN interfaces configured on both Cisco Nexus switches.

* Some of the client application servers are implementing fast-path forwarding for the return traffic.

* Those servers are sending the return traffic to the VLAN interface MAC address instead of the HSRP MAC address.

The network engineer discovers that some traffic is dropped because it passes the vPC peer link to be forwarded out the vPC interface. What must be configured on the vPC switches to resolve the issue?

Options :

A : peer-switch

B : peer-gateway

C : arp synchronize

D : spanning-tree

Answer: B

Question 3

300-615-page127-image12

Refer to the exhibit. An engineer troubleshoots the HSRP configuration and notes that the remote end uses

HSRP version 1. The engineer sets the local HSRP to version 1, but the problem continues. Which action

resolves the issue?

Options :

A :

Change the local group number to 255 or less and request that the remote data center matches the group

number in its configuration.

B : Set the local group number as 300 in the remote data center configuration.

C : Run version 1 and version 2 HSRP on VLAN300 in the local data center.

D :

Reduce the priority of the local HSRP to below 100 to force the local HSRP to standby and then change the

version to version 1.

Answer: A

Question 4

Refer to the exhibit. The EEM script is applied in the default VDC to collect the outputs during high CPU utilization on the Cisco Nexus 7000 Series Switch for all VDCs. Which configuration set must be added to the script to fix the issue?

Options :

A :

switch(config-applet)# event snmp 1.3.6.1.4.1.9.9.109.1.1.1.1.6.1 get-type exact entry-op ge entry-val

50 poll-interval 1

switch(config-applet)# action 0.2 cli enable

switch(config-applet)# action 0.5 cli switchto vdc Core

switch(config-applet)# action 0.8 cli switchto vdc Distribution

B :

switch(config-applet)# event snmp 1.3.6.1.4.1.9.9.109.1.1.1.1.6.1 get-type exact entry-op ge entry-val

50 poll-interval 1

switch(config-applet)# action 0.2 cli config t

switch(config-applet)# action 0.5 cli switchto vdc Core

switch(config-applet)# action 0.8 cli switchto vdc Distribution

C :

switch(config-applet)# event snmp oid 1.3.6.1.4.1.9.9.109.1.1.1.1.6.1 get-type exact entry-op ge entryval 50 poll-interval 1

switch(config-applet)# action 0.2 cli config t

switch(config-applet)# action 0.5 cli switchto vdc Core

switch(config-applet)# action 0.8 cli switchto vdc Distribution

D :

switch(config-applet)# event snmp oid 1.3.6.1.4.1.9.9.109.1.1.1.1.6.1 get-type exact entry-op ge entryval 50 poll-interval 1

switch(config-applet)# action 0.2 cli enable

switch(config-applet)# action 0.5 cli switchto vdc Core

switch(config-applet)# action 0.8 cli switchto vdc Distribution

Answer: D

Question 5

300-615-page127-image37

Refer to the exhibit A customer network uses OSPFv2 and MP-BGP protocols A network administrator installs a new Cisco Nexus Switch in the data center but experiences a BGP RIB failure Which action solves the issue?

Options :

A : Change the administrative distance of OSPF to 220

B : Configure the route as a BGP backdoor

C : Use a filter list for OSPF to filter both routes

D : Implement next-hop-self

Answer: D